Thursday, June 14, 2012

Luggage Tag Tutorial

Hi Y'all!

It has been so long since I have posted anything that blogger has updated!  Wow!  The purpose of this post is for me to share the way I made a luggage tag.  I read through and attempted three different versions I found on Pinterest.  I kind of used a snippet from each of theirs to make mine like I wanted.  These are the ones I tried.  This one was just too "curvy" for my sewing abilities, but I liked the button hole to keep it closed.  Because I purchased the super-firm double sided fusible interfacing called for in the previous tutorial, my tag was just too thick to do this one.  But, I liked the fact that the handle was made from the same fabric instead of ribbon.  Finally, this one was really the simplest, but when I made it then shook the tag upside down, the address label fell out.  So, here is my way.  I am still not crazy with the idea of snipping out the fabric from the window without hemming it, but I just don't think I can think of a better way.  Any suggestions for doing this better are welcome.



Materials:

Vinyl - (1) 2 1/2" x 3 1/2" piece (keep the paper)
Top fabric - (1) 3 1/2" x 5" and (1) 3 1/2" x 5 1/2" piece
Bottom fabric - (1) 3 1/2" x 5" and (1) 2" x 12" piece
Fusible interfacing - single sided fusible is fine for this project - (2) 3" x 4 1/2" pieces
Coordinating thread



Supplies:

Scissors and/or rotary cutter and mat
Iron
Sewing machine - you'll need to be able to do a button hole and a zig-zag stitch
Parchment paper

I went to a quilting store to find the vinyl.  It came in a roll, like this:



You can use whichever stiffness of fusible interfacing you want, it depends on how stiff you want your luggage tags.  Mine was super stiff because I bought it for a different tag than the one I ended up making.  I would suggest one a bit less stiff. It will make it easier to turn inside out.  And, it will probably be less expensive than what I bought.

When I ironed the fabric and fusible interfacing together, I protected my ironing board and iron by folding it into a piece of  parchment paper.  One of the brands of interfacing I used suggested to do this, so I just kept doing it.

The very first thing you want to do is find some fun materials that you like.


Step 1:  Cut out all of your materials.  Don't forget to hold onto the paper from your vinyl!
Step 2:  Iron on the fusible interfacing to the wrong side of one piece of your bottom fabric and the 3 1/2" x 5" piece of your top fabric.


Step 3:  Iron your 2" x 12" piece in half, lengthwise.  Then, open it up and fold each end in to the center.  Then, fold those in half.  You will end up with a 1/2" x 12" piece.  See pictures below.  Sew down the length of this strip, kind of close to the edge, on each side of this folded fabric.  This is the strap of your tag.  Set this aside.

Ironed flat

Ironed in half

 

Open up and iron one side in to the crease

Iron the other side in to the crease


 
Then iron the whole thing in half to be 1/2" wide

 

Here is another strip that shows where to sew, sort of


Step 4:  Make a button hole on the 3 1/2" x 5 1/2" piece of your top fabric, about 1 1/2" from the edge of one end.  The button hole should be a teeny bit wider than the strap, just enough to pullt he strap through.  Now fold the end over and make a hem.  You will want this piece to end up shorter than the actual tag or when you go to sew the end up, you'll have a hard time doing that.  See the picture below the next step to see what I am talking about.  I hope this makes sense.

Step 5:  Now, center your vinyl on the right side of your fabric with the button hole.  You'll want it to be close enough to the button hole that you can zig-zag stitch and be close but not touching.  I kind of centered it across the width.  You just need enough at the opposite end of the button hole end to sew the tag together.  I don't know if I took a picture of this, but hopefully you'll see what I mean in the finished product.  Go ahead and zig-zag stitch all the way around the edge of the vinyl.  You will want to leave the paper on there or your presser foot will stick to the vinyl and it won't move.  This will be very frustrating and you will want to jump up and down (not that I would ever do that).  So, don't try it.  Use the paper.  Here is a picture of the button hole, hem, and vinyl sewn on.  I am apparently not good at documenting.



Step 6:  You can now pull the paper off.  It should come off pretty easily because you  have just perforated it with a zillion holes.  I did a very "close" zig-zag on all but one, so I didn't need to try to pull the paper out of the stitching area on any of them except that one that had a less "close" stitch.  It's a pain.  And a mess.


Step 7:  Now, very close to the stitch, cut your fabric out of the window, like in the picture.  If this isn't clear, let me know.  It might be kind of hard to tell, but you can kind of see it.


Step 8:  Take your piece of top fabric with the interfacing attached and lay it interfacing side down on the table.  Take the window piece and lay it face up on top of this.  Make sure that your hemmed end will be shorter than the end of your tag.  This is your chance to adjust the hem if it isn't.  Lay the piece of bottom fabric with the interfacing attached and lay it interfacing side up.  Now you have an inside out luggage tag sandwich. 
Step 9:  Sew very closely around the edge of the interfacing on the fabric, on all three sides except the edge that has the button hole/hemmed edge.  Leave that one open.
Step 10:  Turn the whole thing inside out (the window stays with the matching fabric).
Step 11:  Now, fold in the edges and sew all the way across the top.  I had to give it two rows of stitching to make sure I got the hem because it was kind of small.  Plus, I ironed the hem in before sewing to make it stay in place. 
Step 12:  Fold the strap in half and line it up with the botton hole, between the window fabric and the upper fabric, but not so far down that you can see if through the window.  You'll kind of have to fold down the window piece, and then sew the strap on there.  I went backwards then forwards twice and made two rows of stitching to make it nice and sturdy.  Pull your strap through the botton hole.


You're all done!  The tag will hold an address label the size of a business card.

Let me know if something doesn't make sense and I'll correct it.  I know that sometimes something that makes sense in my head doesn't make sense to anyone else.  :)

I could never have figured this out on my own, so I am super thankful for the three other tutorials that I went through to get to this one.

I made four of these for my sister for her birthday.  She seemed pleased with them.  Scott was like, well, are you going to make some for us?  Yes, before our cruise in November, I will do that.